|
|
|
|
 
|
Metal twin rudder assembly
£49.99
|
|
|
|
 
|
Exhaust capture -made from stainless steel
Internal diameter 19mm
£17.99
|
|
|
|
|
Exhaust capture - made from stainless steel
Internal diameter 21mm
£17.99
|
|
|
|
|
|
| ProBoat Programming Module
If brushless power alone isn’t enough to satisfy your need for speed, the Pro Boat Brushless Programming Module is what you need to take advantage of the latest Li-Po battery technology. The programming module allows you to program the PRB3309 Blackjack 26 brushless speed control for safe use of Li-Po batteries, with settings for voltage cutoff, brake function, timing, throttle curve and more. Key Features:
-Settings for battery type (Li-Po or Ni-MH)
-High or low voltage cutoff
-Adjustable brake, timing and throttle curve
£19.99
|
Du-Bro Universal Kwik Switch Mount
Install your battery switch in minutes by drilling one 3/16" hole. It's designed to fit most radio switches and is ideal for use in planes, helicopters, cars and boats. It is adjustable to any wall thickness up to 3/8". The on/off switch mount plunger fits tightly into the mounting bracket, this will help keep the water out of the boat. We suggest a little grease on the metal shaft to also help this.
£3.99 |
|
|
|
|
|
|
Pushrod Seals
These Pushrod Seals with Mounting Hardware are for Boat Use. They are used to make a water-resistant seal where the pushrods exit the boat. These seals are designed for use with 2-56 or 4-40 pushrods. They also make a fuelproof seal.
Instructions: Drill hole for pushrod. Center flange and drill pilot holes for screws. Soften boot in a cup of hot water. Slip boot and flange over pushrod and mount with screws. After all pushrod adjustments are made put a drop of CA glue on the nipple to make a permanent seal.
£3.99
|
Octura Auto Bailer
Use this to help get rid of water in you hull. The aluminum bailer has a small plastic ball that moves to allow water to exit your hull while your running your boat, but when your boat is at rest the outside water pressure pushes the ball into a seal that closes the hole.
£6.99 |
|
|
|
|
  
|
Aluminium Servo tray
This aluminum servo mount can either be mounted in your boat, standing up on laying down. Its made for standard size servos
£7.25
|
|
|
|
|
|
This is the AquaCraft Marine Brushless Motor for use
with the AquaCraft Super Vee 27
FEATURES: Direct replacement motor
Brushless In-Runner design
Pre-installed 3.5mm gold bullet connectors
INCLUDES: One B36/56 Brushless Marine Motor
REQUIRES: Installation
SPECS: Length of can: 2.07" (53mm)
Length including shaft: 2.8" (72.77mm)
Stator length: 56mm
Diameter: 1.42"(36mm)
Shaft diameter: 5mm
£49.99
|
Proboat 45amp ESC
45-Amp Brushless ESC Key Features:
Rev limiter allows brief operation of the motor out of the water to protect the motor and drivetrain components.
Water cooled for optimum performance.
The soft start feature slightly limits current to increase the life of the electronic components.
The ESC also features a cutoff voltage indicator that will stop the motor from operating if the batteries are reaching full discharge
High-power FET control with proportional forward
High-frequency design delivers smooth speed transition.
Pre-wired with Dean’s battery plug, bullet-style motor connectors and universal receiver plug that fit JR, Hitec, Airtronics Z, Futaba and new KO radios
Pre-programmed for use with Ni-MH batteries. Can be programmed for use with Li-Po batteries with -PRB3311 Programming Module (sold separately)
Specs:
Forward:Yes
Brake:Yes
Continuous Maximum Current:45A
Input Voltage:Minimum 10V, Maximum 21V
Momentary Peak Current:55A
BEC Voltage:5.8V
£59.99
|
|
|
|
 |
 |
Product ID: grp-2317.40
Graupner K Series 40mm
Graupner Carbon Fiber Props are light, sharp and don't need to be balanced or sharpened! Looking at the back of the boat these props spin counter clockwise. These fit 3/16" prop shafts with drive dogs.
£3.99
|
Product ID: grp-2317.42
Graupner K Series 42mm
Diameter 42mm(1.65"), Pitch 1.4x42=58mm or 2.31" These Props are light, sharp and don't need to be balanced or sharpened! Looking at the transom these props spin counter clockwise. Fit 3/16" shafts w/drive dogs.
£3.99
|
|
|
|
|
|
|
Product ID: grp-2317.45
Graupner K Series 45mm
Diameter 45mm(1.77"), Pitch 1.45x45=63mm or 2.48" These Props are light, sharp and don't need to be balanced or sharpened!
Looking at the transom these props spin counter clockwise. Fit 3/16" shafts w/drive dogs.
£3.99
|
Product ID: grp-2317.48
Graupner K Series 48mm
Diameter 48mm(1.89"),
Pitch 1.4x48=67mm or 2.64"
These Props are light, sharp and don't need to be balanced or sharpened!
Fit 3/16" shafts w/drive dogs.
£3.99
|
|
|
|
 |
|
Product ID: grp-2317.51
Graupner K Series 51mm
Diameter 51mm(2.01"), Pitch 1.4x51=71 mm or 2.80" These Props are light, sharp and don't need to be balanced or sharpened! Looking at the transom, these props spin counter clockwise. Fit 3/16" shafts w/drive dogs.
£3.99
|
Product ID: grp-2318.37.5
Graupner 37.5 for 4mm threaded shafts
Diameter 37.5mm, Pitch 52mm.These Props are light, sharp and don't need to be balanced or sharpened! Looking at the transom, these props spin counter clockwise. Fit 4mm threaded shafts.
£2.99
|
|
|
|
 |
|
Product ID: grp-2318.36
Graupner 36mm for 4mm threaded shafts
Diameter 36mm, Pitch 50mm.These Props are light, sharp and don't need to be balanced or sharpened! Looking at the transom, these props spin counter clockwise. Fit 4mm threaded shafts.
£2.99
|
Product ID: grp-2318.33
Graupner 33mm for 4mm threaded shafts
Diameter 33mm, Pitch 46mm.These Props are light, sharp and don't need to be balanced or sharpened! Looking at the transom, these props spin counter clockwise. Fit 4mm threaded shafts.
£2.99
|
|
|
|
 |
|
Product ID: grp-3344
Graupner 1/8" to 4mm flex coupler
The ends of this coupler are joined by a piece of flex cable. This allows a slight bend in the coupler. Making it easier to install your motor.
£7.39
|
Product ID: grp-3345
Graupner 5mm to 4mm flex coupler
The ends of this coupler are joined by a piece of flex cable. This allows a slight bend in the coupler. Making it easier to install your motor.
£7.39
|
|
|
|
 |
|
Robbe 1494 coupler
3.1mm to 2.5mm
£3.59
|
Graupner 2375 coupler
for shaft diameter 3.2 mm to 2.0 mm
£5.49
|
|
|
|
 |
|
Graupner 3382 coupler
For 4 mm diam. shafts
£2.99
|
Graupner 355.3 flexible coupler
The shaft coupling is made of top quality plastic with metal inserts. In the case of considerable vertical differences in line-up of main drive units mounted at an angle to each other, a compensating member must be installed. Maximum operating angles per joint is 10°. Exchange universal joints give still more connecting possibilities. Shaft coupling without compensating member. For shafts Ø 2+2,3 mm
£3.99
|
|
|
|
 |
|
Graupner 3346 coupler
For 3.2 mm diam. Shafts
£3.49
|
Graupner 3374 coupler
For coupling 4 mm diam. shafts to a 5 mm diam. shaft.
£2.49
|
|
|
|
 |
|
Graupner 3373 coupler
For 5 mm diam. Shafts
£2.49
|
Graupner 1157.2 coupler
Hi-impact plastic. For mounting E-motors SPEED 500 through 700 and ULTRA 920 through 930.
£3.99
|
|
|
|
 |
|
Hatch tape
Great for sealing your hatch to help keep out water in the event of a capsize
£1.99
|
Plastic prop 36mm x 25mm
2 in packet Dogged drive for 3/16th
£3.99
|
|
|
|
 |
|
 |
|
P104 Brushless motor mount
Includes aluminum mount, rubber cushion, stainless steel 3mm x 8mm socket head screws for mounting brushless motor, stainless steel washers, 2.5mm hex wrench, two nylon pull-ties for securing your motor, plus a 3-1/8" x 2-1/16" x 3/16" hot-press laminated domestic mahogany plywood base with pre-installed 6-32 blind nuts, stainless steel 6-32 x 5/16" socket head screws, stainless steel washers, and a long 7/64" hex wrench.
£14.99
|
|
|
|
|
M122 motor mount
540/550 Motor Mount 80 Degree - Fits Vac-U-Cracker. Great for any through-hull drive installation. Includes 2ea M-3 motor face-mount screws. Strong 3/32 Laser-Cut aluminum. Resists bending. 50% thicker than regular 1/16 inch thick aluminum mounts. Perfect as a Brushless Motor Mount for 540 size motors. Mounting holes 1" on-center. The base has 1.125" c/c mount holes and a 0.75" center hole that will bolt up to most 600 size motors.
£7.99
|
Graupner 1711 motor mount
Product information
Suitable for electric motors having outer diameters of 35 through 45 mm.The motor is fastened by a clamp in a prismatic recess of the motor mount. The motor mount is formed of rigid plastic. The base plate sports oblong 4 mm holes to permit proper alignment of motor shaft and propeller shaft.
£9.99
|
|
|
|
 |
|
Plastic prop 36mm x 27mm
2 in packet Dogged drive for 3/16th
£3.99
|
Plastic prop 36mm x 30mm
2 in packet Dogged drive for 3/16th
£3.99
|
|
|
|
 |
|
Plastic prop 36mm x 32mm
2 in packet Dogged drive for 3/16th
£3.99
|
Watercooling coil for speed 500/600
£8.99
|
|
|
|
 |
|
|
Watercooling coil for speed 700
£8.99
|
Robbe 1472
Dynamic 3-blade boat propellers
Diameter: 50.00 mm
No of Blades: 3
Pitch: 42
Thread: M 4
Direction of rotation: left hand
£2.99
|
|
|
|
|
|
 |
Robbe 1471
Dynamic 3-blade boat propellers
Diameter: 50.00 mm
No of Blades: 3
Pitch: 42
Thread: M 4
Direction of rotation: right hand
£2.99
|
Graupner 3356 rubber bellows
Pack contains 2. For waterlight linkages. 32 mm long, opening 1.5 and 5 mm diameter.
£3.00
|
|
|
|
|
|
|
